+8617773160488

Our Factory

EN
All Categories

Monel

You are here : Home>Product>Material>Monel

  • https://www.alloy-ronsco.com/upload/product/1633942706428081.jpg
  • https://www.alloy-ronsco.com/upload/product/1633942724439757.jpg
  • https://www.alloy-ronsco.com/upload/product/1633942724521322.jpg
  • https://www.alloy-ronsco.com/upload/product/1633942724835614.jpg
  • https://www.alloy-ronsco.com/upload/product/1633942724510370.jpg
  • https://www.alloy-ronsco.com/upload/product/1633942724948793.jpg
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6

China Factory Special Steel Nickel Alloy High Quality Monel K-500 for Petrochemical & Refinery Environmental Food Processing

Monel K-500 (N055000) Monel alloy is a corrosion-resistant alloy with the largest consumption, the most versatile and excellent comprehensive properties. This alloy has excellent corrosion resistance in hydrofluoric acid and fluorine gas media, and also has excellent corrosion resistance to hot concentrated lye.

The chemical composition of Monel K-500 (N055000) Monel alloy is mainly composed of 30% Cu and 63% Ni plus a small amount of Fe (1%-2%). Compared with monel400, aluminum and titanium are added.

Monel K-500 alloy has corrosion resistance equivalent to 400, but has higher mechanical strength and hardness. It has good thermal corrosion resistance and long-term structural stability. Mainly used to manufacture turbine blades and gas turbine blades on aero engines whose working temperature is below 750℃ ; used to manufacture fasteners and springs on ships; pump and valve parts on chemical equipment ; scraper blades on papermaking equipment Wait.

  • Product Description
  • Inquiry

Model: Monel K-500 (UNS N05500)
Brand: Ronsco


Ronsco Alloy K-500 Parameter Table
MONEL® K-500, UNS N05500, W.Nr.2.4375, NiCu30Al
Genenal Introduction
Monel K500 is a precipitation-hardenable Ni-Co alloy that combines the excellent corrosion resistance characteristic of Monel 400 with the added advantage of greater strength and hardness. These amplified properties, strength and hardness, are obtained by adding AL and Ti to the Ni-Co base and by a thermal processing used to effect precipitation, typically called age hardening or aging. When in the age-hardened condition, Monel K-500 has a greater tendency toward stress-corrosion cracking in some environments than Monel 400. Alloy K-500 has approximately three times the yield strength and double the tensile strength when compared with alloy 400. Plus, it can be further strengthened by cold working prior to precipitation hardening. The strength of this nickel based alloy is maintained to 1200° F but stays ductile and tough down to temperatures of 400° F. Its melting range is 2400-2460°F.

This nickel alloy is spark resistant and non-magnetic to -200°F. However, it is possible to develop a magnetic layer on the surface of the material during processing. Al and Co may be selectively oxidized during heating, leaving a magnetic nickel rich film on the outside. Pickling or bright dipping in acid can remove this magnetic film and restore the non-magnetic properties.


Chemical Composition:
ContentCSi MnSNiCrCoMoCuFeBiAlTiBAl+Ti
Min



63.00 


27.00 

2.30 0.35 

Max0.18 0.50 1.50 0.01



33.00 2.00 
3.15 0.85 


Forms & Specifications
Sheet, Plate, Strip:
BS3072 NA18
QQ-N-286
DIN 17750
ISO 6208
H4551
Bar, Rod:
AMS 4676
ASTM B865
BS3076 NA18
DIN 17752
QQ-N-286
ISO 9723/ISO 6208
H4553
Wire:
BS3076 NA18
ISO 9724
DIN 17753
QQ-N-286
H4554
Forging:
DIN 17754
QQ-N-286
ISO 9725
Other:
UNS N05500, BS6076 NA13, Trade name Monel® Alloy K-500, Werkstoff Nr. 2.4375, MIL-N-24549, NACE MR-01-75
Physical PropertiesApplication:
Density: 8.44g/cm³, 0.305lb/in³
Alloy K-500 can be hardened by cold working and by heat treating, supplied in half hard and full hard temper.

Mean Coefficient of Thermal Expansion: in/in/°F (mm/m/°C):
70 - 212 °F (20 - 100 °C): 7.6 x 10-5 (13.7)
Modulus of Elasticity: KSI (MPa):  26 x 10³ (179 x 10³) in Tension
Magnetic Permeability, H=200: Annealed <1.002
Melting Point: 2460 °F (1350 °C) approx.
Pump components,
Doctor blades and scrapers
Oil well drill collars and cable wrap
Marine instruments
Electronic components
Springs
Valve tray
Submarine parts 
Typical  Mechanical Property Ranges:
Form & ConditionTensile StrengthYield Strength 0.2% OffsetElongation %
min. 
Hardness
max.
KsiMpaKsiMpaHB
(3000kg)
HRC
Rod and Bar






      Hot-Finished 90-155621-106940-110276-75845-20140-315 75B-35C
      Hot-Finished, Aged140-190965-1310100-150 690-103430-20 265-346 27-38C
      Hot-Finished, Annealed90-110621-75840-60 276-41445-25 140-185 75-90B
      Hot-Finished, Annealed and Aged130-165 896-1138 85-120586-82735-20250-315 24-35C
      Cold-Drawn, As-Drawn100-140690-965 70-125 483-862 35-13175-260 88B-26C
      Cold-Drawn, Aged135-185 931-1276 95-160 655-1103 30-15255-370 25-41C
      Cold-Drawn, Annealed90-110 621-758 40-60276-41450-25140-18575-90B
      Cold-Drawn, Annealed and Aged130-190 896-131085-120 586-82730-20250-315 24-35C
Sheet, Cold-Rolled, Annealed90-105 621-724 40-65 276-44845-25-85B max
Strip, Cold-Rolled






      Annealed90-105621-724 40-65 276-448 45-25-85B max
      Annealed and Aged130-170 896-117290-120621-827 25-15-24C min.
      Spring Temper145-165 1000-1138 130-160896-1103 8-3-25C min.
      Spring Temper, Aged170-2201172-1517130-195 896-1345 10-5-34C min.
Tube and Pipe, Seamless






      Cold-Drawn, Annealed90-110621-758 40-65 276-448 45-25- 90B max.
      Cold-Drawn, Annealed and Aged130-180 896-124185-120 586-82730-15-24-36C
      Cold-Drawn, As-Drawn 110-160758-110385-140 586-965 15-2- 95B-32C
      Cold-Drawn, As-Drawn, Aged140-220965-1517100-200690-1379 25-3-27-40C
Plate






      Hot-Finished90-135 621-931 40-110 276-758 45-20 140-260 75B-26C
      Hot-Finished, Aged140-180 965-1241100-135 690-98130-20 265-337 27-37C
Wire, Cold Drawn






      Annealed 80-110 552-758 35-65 241-44840-20--
      Annealed and Aged120-150 827-103490-110 621-758 30-15--
      Spring Temper 145-190 1000-1310 130-180896-12415-2--
      Spring Temper, Aged160-200 1103-1379140-190 965-1310 8-3--


The advantage of Ronsco
1,Price lower than Europe, USA 20~30%.
2,100% quality guaranty because we remelt by VIM+ESR.
2,Best Service: 0 payment if you test not ok. 
3,0 fee for UT, PT. 
4,Low MOQ for new materials: 200kg.
5,Fast 20~30 days of lead time for new materials.


For More Information About Monel K-500 (UNS N05500/ W.Nr. 2.4375) Pipes, Plates, Tubes, Sheets, Bars , please call +86 17708476248 or Send an Email to [[email protected]]

Contact Us